Your cookie settings.

Personalised experiences at full control.

This website uses cookies and similar technologies (“cookies”). Subject to your consent, will use analytical cookies to track which content interests you, and marketing cookies to display interest-based advertising. We use third-party providers for these measures, who may also use the data for their own purposes. 

You give your consent by clicking "Accept all" or by applying your individual settings. Your data may then also be processed in third countries outside the EU, such as the US, which do not have a corresponding level of data protection and where, in particular, access by local authorities may not be effectively prevented. You can revoke your consent with immediate effect at any time. If you click on "Reject all", only strictly necessary cookies will be used.
Sino-foreign joint venture High-tech enterprise, specializing in providing customers with stable and reliable bearing products and overall technical solutions.
简 / EN
You are here: Home » Products » Agricultural Machinery Bearings » W square hole non-relubrication series
 
Agricultural Machinery Bearings
The outer spherical ball bearing is actually a variant of the deep groove ball bearing, which is characterized in that its outer ring outer diameter surface is spherical, which can be fitted into the corresponding concave spherical surface of the bearing seat to play a self-aligning role. The outer spherical bearing is mainly used to bear the combined radial and axial load mainly radial load, it is generally not suitable to bear the axial load alone.
Although its basic performance should be similar to that of deep groove ball bearings, but most of these bearings are used in relatively rough machinery, the installation and positioning are not accurate enough, the alignment of the axis of the shaft and the seat hole is poor, or the shaft length and deflection In the case of decent, and the accuracy of the bearing itself is not high enough, and some structures are also relatively rough, so the actual performance of the performance of the deep groove ball bearings of the same specifications should be discounted. For example: the outer spherical ball bearing with top wire is applied to the through shaft with large difference in rigidity and deflection. This bearing has sealing rings on both sides, which can strictly prevent the intrusion of dirt.
Appropriate amount of lubricant, no need to clean before installation, no need to add lubricant, when the top screw on the protruding end of the bearing inner ring is fastened on the shaft. The allowable axial load must not exceed 20% of the rated dynamic load.
  • R3 seal: used for conventional Z&R insert bearing products. The vulcanized triple-lip contact seal made of low-friction nitrile rubber (NBR) compound is bonded to the inner surface of the steel frame through vulcanization. The triple lip strongly prevents dust and muddy water It can ensure the life of the bearing even in severe environmental conditions, and is suitable for under 1000RPM/Min.)
  • R5 seal: used for maintenance-free products of Z&R insert bearings, suitable for extremely polluted environments, such as agricultural machinery and chemical equipment applications, through vulcanization, vulcanized five-lip contact seals made of low-friction nitrile rubber (NBR) compounds Fitted to the inner surface of the steel frame, the steel frame is fixed in place by the seal groove in the outer ring of the bearing, and can protect the seal from solid contamination; the 5 layers of sealing lips have different designs to provide excellent sealing performance to deal with Different working conditions including dynamic misalignment; the sealing lip is a labyrinth type to prevent various pollutants from entering and grease leakage. Suitable for 800RPM/Min or less.
  • FJ seal: used for Z&R outer spherical bearing ultra-high-speed products; suitable for low-noise environments, such as blowers, commercial fans, etc.;
After being specially treated by Viton, it is attached to the inner surface of the stamped steel sheet frame, and a non-contact structure stamped steel sheet is added to effectively prevent the entry of pollutants; it can run smoothly in an environment of up to 200° .
  • F seal: used for Z&R insert bearing conventional products, two steel galvanized sheets are sandwiched with nitrile rubber (NBR) seal, the sealing lip is axially pre-tightened, and the outer steel galvanized sheet has a certain angle outward Inclined and extended to effectively protect the sealing lip from mechanical damage and particulate entry; this structure is suitable for occasions that require both high speed and low noise.
SF seal: The nitrile rubber (NBR) sealing lip is vulcanized and adhered to the inner surface of the stamped steel sheet frame. Through its non-contact steel sheet frame, the steel sheet frame is fixed in place by the sealing groove in the outer ring of the bearing. The shoulder of the ring forms a small gap; the steel retaining ring is installed on the shoulder of the inner ring by interference fit, which can significantly improve the sealing effect without increasing friction to prevent the seal from being affected by particle contamination .
 

密封圈材料对比

(Sealing ring material comparison)

聚合物材料类型

(Polymer material type)

丁腈橡胶

(Nitrile rubber)

硅胶

(Silica gel)

氟胶

(Viton)

材料代号

(Material code)

NBR

Si

Viton

耐温范围

(Temperature range)

-40F ~250F

(-35℃~120℃)

-80F ~400F

(-60℃~200℃)

-40F ~400F

(-35℃~200℃)

耐油

(Oil resistant)

E

G

E

耐酸

(Acid resistant)

G

F

E

耐碱

(Alkali resistance)

G

X

F

耐水

(Water resistant)

G

G

G

耐热

(Heat resistant)

G

E

E

耐寒

(Cold resistant)

G

E

F

耐磨

(Wear-resistant )

E

G

E

耐臭氧

(Ozone resistant)

G

E

E

E=优秀(  Excellent) G=好 (Good)  F=普通(ordinary) X=不推荐(Not recommended)